Difference between revisions of "LSL Protocol/Restrained Love Open Relay Group/simwide"
Dahlia Orfan (talk | contribs) |
Dahlia Orfan (talk | contribs) |
||
| (One intermediate revision by the same user not shown) | |||
| Line 12: | Line 12: | ||
The relay must answer ok if and only if the source is a grabber. Otherwise the answer is always ko. The effect of this command is as follows: for any command @getsomething:xxx=channel, the relay must listen to the viewer's answer and resend it using llRegionSayTo() using the same channel and to the source. So !x-simwide enables to use such command with a hud which is more than 100m away (simwide mode). | The relay must answer ok if and only if the source is a grabber. Otherwise the answer is always ko. The effect of this command is as follows: for any command @getsomething:xxx=channel, the relay must listen to the viewer's answer and resend it using llRegionSayTo() using the same channel and to the source. So !x-simwide enables to use such command with a hud which is more than 100m away (simwide mode). | ||
Typical exchange: | Typical exchange (if C is already accepted by the relay) in chat session: | ||
C -chat on RLVRC-> R: enable_forward,!x-simwide | C -chat on RLVRC-> R: enable_forward,!x-simwide | ||
| Line 20: | Line 20: | ||
R --llOwnerSay--> V: @getoutfit=1111 | R --llOwnerSay--> V: @getoutfit=1111 | ||
R <-chat on 1111- V: 0010011111111110 | R <-chat on 1111- V: 0010011111111110 | ||
C <-chat on | C <-chat on 1111- R: 0010011111111110 | ||
C -chat on RLVRC-> R: disable_forward,!x-simwide/clear | C -chat on RLVRC-> R: disable_forward,!x-simwide/clear | ||
C <-chat on RLVRC- R: disable_forward,!x-simwide/clear,ok | C <-chat on RLVRC- R: disable_forward,!x-simwide/clear,ok | ||
Latest revision as of 07:49, 11 June 2011
simwide
STATUS: deprecated
version: 000
Two new commands !x-simwide and !x-simwide/clear explained below.
Description of !x-simwide
The relay must answer ok if and only if the source is a grabber. Otherwise the answer is always ko. The effect of this command is as follows: for any command @getsomething:xxx=channel, the relay must listen to the viewer's answer and resend it using llRegionSayTo() using the same channel and to the source. So !x-simwide enables to use such command with a hud which is more than 100m away (simwide mode).
Typical exchange (if C is already accepted by the relay) in chat session:
C -chat on RLVRC-> R: enable_forward,!x-simwide C <-chat on RLVRC- R: enable_forward,!x-simwide,ok C -chat on RLVRC-> R: outfit_query,@getoutfit=1111 C <-chat on RLVRC- R: outfit_query,@getoutfit=1111,ok R --llOwnerSay--> V: @getoutfit=1111 R <-chat on 1111- V: 0010011111111110 C <-chat on 1111- R: 0010011111111110 C -chat on RLVRC-> R: disable_forward,!x-simwide/clear C <-chat on RLVRC- R: disable_forward,!x-simwide/clear,ok
Interaction with !x-takeover
These instructions must be used only with llRegionSayTo(). So the relay will have to save the uuid key of the grabber and also will have to update it after a !x-takeover.
Interaction with !x-handover
After a !x-handover, the next grabber must send a new !x-simwide to enable the simwide mode again.